Poulan 115153026 Bedienungsanleitung PDF herunterladen (Seite 15)

15

NOTE: It is normal for a small amount of oil

to appear under the saw after engine stops.

Do not confuse this with a leaking oil tank.

S ON/ST OP Switch -- Ensure ON/STOP

switch functions properly by moving the

switch to the STOP position. Make sure en-

gine stops; then restart engine and continue.

S Fuel Tank -- Do not use saw if fuel tank

shows signs of damage or leaks.

S Oil Tank -- Do not use saw if oil tank shows

signs of damage or leaks.

CHECK FOR LOOSE

FASTENERS AND PART S

S Bar Nuts

S Chain

S Muffler

S Cylinder Shield

S Air Filter

S Handle Screws

S Vibration Mounts

S Starter Housing

S Front Hand Guard

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull

chain makes a sawdust powder and cuts

slowly. S ee CHAIN SHARPENING.

CHECK GUIDE B AR

Conditions which require guide bar mainte-

nance:

S Saw cuts to one side or at an angle.

S Saw has to be forced through the cut.

S Inadequate supply of oil to bar/chain.

Check the condition of guide bar each time

chain is sharpened. A worn guide bar will

damage the chain and make cutting difficult.

After each use, ensure ON/STOP switch is

in the STOP position, then clean all sawdust

from the guide bar and sprocket hole.

To maintain guide bar:

S MoveON/STOPswitchtoSTOP.

S Loosen and remove bar nuts and clutch

cover. Remove bar and chain from saw.

S Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal

process of rail wear . Remove these burrs

with a flat file.

S When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct GrooveWorn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when ex-

cess heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw .

CHECK FUEL MIXTURE LEVEL

S See FUELING ENGINE under the OP-

ERA TION section.

LUBRICATION

Bar Oil

Fill Cap

S See GUIDE BAR AND CHAIN OIL under

the OPERATION section.

INSPECT AND CLEAN U NIT AND

DECALS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

S Wipe off unit with a clean dry cloth.

CHECK CHAIN B RAK E

See CHAIN BRAKE in the OPERATIO N

section.

CLEAN AIR FILTER

CAUTION:

Do not clean filter in gasoline or

other flammable solvent to avoid creating a

fire hazard or producing harmful evaporative

emissions.

Cleaning the air filter:

A dirty air filter decreases the life and perfor-

mance of the engine and increases fuel con-

sumption and harmful emissions. Always

clean your air filter after 10 tanks of fuel or 5

hours of operation, whichever comes first.

Clean more frequently in dusty conditions. A

used air filter can never be completely

cleaned. It is advisable to replace your air fil-

ter with a new one after every 50 hours of op-

eration, or annually, whichever comes first.

1. Loosen 3 screws on cylinder cover .

2. Remove cylinder cover .

3. Remove air filter cover and air filter.

4. Clean the air filter using hot soapy water.

Rinse with clean cool water. Air dry com-

pletely before reinstalling.

5. Reinstall air filter and air filter cover.

6. Reinstall cylinder cover and 3 screws.

Tighten securely.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21

Kommentare zu diesen Handbüchern

Keine Kommentare