Poulan 420917 Bedienungsanleitung

OWNER'S MANUALMODEL NUMBER:961980021SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the

10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla

11OPERATIONTO MOVE FORWARD AND BACKWARD (See Fig. 15)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction

12TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

13OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter

14GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

16WARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF position.2. Remove saf

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

18SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)AUGER HOUSING / IMPELLER ASSEMBLY2 (EXPLODED)2109111113121241314151787115611161835192122

21REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

23REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

24REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

25REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

26REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

27REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

28REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

29REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

31REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

32REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

33NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

34REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)WHEELS1201.06.005-AKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO.

35REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)WHEELSKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U

36REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIM

37REPAIR PARTS SNOW THROWER - MODEL 961980021 (96198002100)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 2

38SERVICE NOTES

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(2) SHEAR BOLTS 1/4-20 x 1-3/4(198636)(2) SPACERS(198638)(1) WASHER 3/8(191

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng