Poulan XT 96192003502 Bedienungsanleitung

OWNER'S MANUALMODEL NUMBER:XT11530ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the

10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla

11OPERATIONTO MOVE FORWARD AND BACKWARD (See Fig. 15)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction

12TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

13OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter

14GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

16WARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF position.2. Remove saf

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

18SERVICE AND ADJUSTMENTSENGINESee engine manual.CARBURETORYour carburetor is not adjustable. Engine performance should not be affected at altitudes u

19STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

21SERVICE NOTES

22REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

23REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

24REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

25REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

26REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

27REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

28REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

29REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

31REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

32REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

33REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

34REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

36KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)CHASSIS

37REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)WHEELSKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONNO

38REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)WHEELSKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U

39REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIM

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(1) LOCKNUT 5/16-18(751153)(1) CARRIAGE BOLT 5/16-18 x 5/8(72250505)(1) LOC

40REPAIR PARTS SNOW THROWER - MODEL XT11530ES (96192003502)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN

41SERVICE NOTES

42SERVICE NOTES

43SERVICE NOTES

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONON / OFF switch - used to STOP the engine.Traction drive control lever - used to engage power-pro pelled for ward or reverse motion of snow